Search results

Does anybody have pics of the EVO bolt on coilover kit on a two door with 37s and running it as low as possible?. And what are the bump stop to bump stop measurements ( standard bump stops).

OK I know there has been many threads on this but, I dont believe I have seen this specifically asked, Are 5.13s in a D44 strong enough to run 37s??? Thanks

Just had a chance for a great pic today, Australia and the most iconic US built car Ever, love Australia, love the US and love Jeeps. See the picture below. I forgot to upload it.

What size bump stops will I need for 37s on a 2 door?

Guys, I have a LED Headlight issue, I have installed LED Headlights with PWM ( pulse width modulation), now the lights do not flicker, however they do turn on and off intermittently, when first on no worries, then after a couple of seconds low beam will go off on one light, then high on the...

I was wondering if anybody has used headers on their JK. I have a leaking and cracked standard exhaust manifold on my JK and I had my local shop order a new on and when it arrived, it is very different. The new one is a header not a cast one like standard. I just wanted to know if anyone has...

Can anyone out there tell me the length of adjustable control arms, for a JKU with 4.5 inch lift, so I can get 8 degrees of castor in the front and so I can get the castor in the rear as close to factory as possible, I know there are a lot of variables such as bumper, winches and load that is...

Can anyone please tell me the free standing height of the 3 inch and 4 inch EVO Plush Ride Coils.

I sent this to ORE and have not got a reply yet, "Can you please tell me what is the extended length of the King Shocks used with the 3" and 4" Enforcer kit? I have Fox Shocks that are 28.2 inch in the front and 28.5 inch extended in the rear, before I order Plush Rides I want to make sure that...

I think this has been asked before but I can not find it, is a ProRock 44 sufficient for 37s when locked???? I am going to wheel my D30 on 35s until it dies and then upgrade and a 44 is about as big as the budget will allow. I occasionally run some rocks, mostly just trails, never high speed stuff.

I need help, I have 4.5inch Synergy springs and AEV drop brackets, I have had a wheel alignment done after installing new ball joints on the tie rod, steering rod and in the Cs. The castor is at 4.1 degrees and the toe was set at 1.0 degree positive(toe in). I have yet to do the ball joint on...

Guys, I am concidering coilovers what I need to know is, I am looking at the EVO Bolt On Kit, what is the lowest I can run the kit? And when being run at their lowest ride height is there much shaft sticking out of the bottom of the coilover, and how does this effect the on road ride, is the...

Has anybody had a "nobus"message apperar in the instrument cluster when the car is switched to the on position, I had this happen today and the car will not go, has anyone had this happen and know what it means????????

Is anybody running Synergy 4.5 inch springs, what are they like, are they stiff or soft?, have you had any sagging issues? Thanks

Can anyone please tell me if the 3" or 4" Evo Plush Ride Coils will stay seated at full flex with Fox Remote Resi 28.3" long shocks, (28.3" open) I would prefer to have 3" but will go with 4" if needed. At the moment I have 3.5" AEV Coils and they are too short at full flex. Any help would be...

How many people are using them and what are your thoughts?, Good bad or otherwise, I am thinking of using then in the front and rear. Any advice would be good.

Has anyone used IKON coil springs, I would like to know what the ride is like, soft or hard? Any other information good or bad.

I am wanting to run a 50" lightbar (I currently run a 20") and it flickers a bit, can anyone tell me if I need a modulation unit (for the 50") like the truck lights to have to stop any flickering. If I do does anyone know which is the best and where to get it??

OK after being a member here for a long time and on my second JK I'm going to ask a noob dumb question, now before I ask I need to tell you that I don't personally know anybody with long arms because we are not allowed to run long arms until I found an engineer that will give me a certificate...

This is a bit of a noob question but it is one that I have never been able to figure out, When measuring a shock where do you measure from, for example, front shock, Do you measure from the middle of the eye on the bottom to the tip of the post on top OR From the middle of the eye on the bottom...