Search results

One thing that needed attention was the location of the canister. I had moved it above the rear axle which is common but there wasn't enough clearance with my trussed 14 bolt. Today I cut the ends off of the mounting bracket and welded a piece of angle on it. I bolted it to the rear crossmember...

I used the Mopar 392 radiator and transmission cooler. It required fabricating new lower mounts and mods to make the JK condenser fit. I have the JK fan rigged for use now while waiting on the 392 fan that is on national backorder. The tune supplied by RPM Extreme works great and only required a...

I decided to do the LS swap. I used the base RPM Extreme kit with a L96 and 6L80. I rebuilt the transmission and upgraded it with a Sonnax valve body kit and clutch pack upgrades. Installed a new Mopar fuel pump assembly while the body was off. The bottom picture shows the radiators. L to R...

The TIPM receives a variable reading from the fuel sender depending fuel level. The TIPM calculates the level also using time and vehicle speed. The TIPM sends a CAN signal to the gauge cluster for it to display the correct level. I replaced a defective sender in a Dodge pickup that would...

So far so good on the 392 radiator keeping the LS cool with only the JK fan rigged in for temporary use. The 392 fan is on national backorder. I wasted money by ordering the cooling package since I didn't use the condenser.

Did you get the issue solved? My Jk LS swap has the same problem.

The 392 radiator has 84 tubes and the JK radiator has 60. Less coolant volume through the 392 tubes since they are thinner. Maybe that is how they are gaining heat transfer in the small size.

I don't see how the small 392 radiator can keep the engine from overheating. It is the same thickness as the 3.8 JK radiator, same width and slightly shorter. They both have a single tube design that is approx. 1" wide. The 392 radiator does have a tube spacing of approximately .235 and the JK...

Fingers crossed. I ordered from another site at a slightly higher price and got a reply that it is on order from the factory.

Just now got an email stating order is cancelled due to availability.

I ordered it and will see if I can make most of it work with my JKU LS swap. I should be able to sell it at a loss if it doesn't work.

It appears that it will let me add it to the shopping cart...

Has anyone got a good look at the factory 392 cooling system. It appears to have an oil cooler and an auxiliary radiator. 68481138AB is the entire cooling unit and it is under $600. The radiator is around $150. The online Mopar part sites don't have very good detail on the auxiliary radiator or...

I would request a schematic and make sure that all of the A/C wires go to the correct locations on the connectors on the new harness also. Especially the under dash harness. It is possible that a mistake was made during the harness assembly.

Is the scan tool turning on the compressor through the GM side only? I would make sure the solder connections have been double checked that tie the Jeep harness to the new harness. Then make sure every crimp connection is tight on the A/C wiring and all grounds on the new harness. If all that is...

My regular insurance company didn't offer anything to cover modified vehicles. I got Stated Value policies on my Cummins powered K30 and my F750 hauler from Progressive. My wife's cousin lost thousands when his customized Chevy pickup was stolen and he had normal full coverage insurance.

Praying for you and your wife. My wife and I also have Covid now but it hasn't been severe. We are triple vaxed but also took some Ivermectin when we first got sick. There is a massive outbreak in our town.

I have good luck using the florescent dye and black light to find leaks.

It was originally a 12' LQ with a wet bath. It is now 14' with a larger dry bath and a closet. Vintage sells them in 12', 14', and 16' LQ.

I like it better than the previous one with home made LQ. The 7'6" height is much better than the 6'6" of my previous one. I had to haul the buggy with one front tire on the floor and the other over the fender with the added platform. No way a taller rig would fit without installing smaller...